|
|
|
|
6100
MOTOR PULLEY PULLER
Removes blower or motor pulley from shaft.
PKG___QTY___WT Label.......5......17.2 |
|
|
|
6752 - 6757
BLOWER SHAFT PLUG
Use as a plug to remove blower pulley on coolers with hollow shafts.
PN____SIZE__PKG__QTY__WT 6752.....3/4"...Clam.....5......0.3 6755......1".....Clam.....5......0.6 6757..3/4&1"..Clam.....5......0.7 |
|
|
|
6122 to 6124
ZINC VARIABLE MOTOR PULLEYS
3-1/4" x 1/2"- 1/3 HP
IMPORTANT: Variable Pulleys must be opened 2-1/2 to 5 full turns (depending on air resistance) or motor will overheat. If motor cycles (stops and starts due to over-heating), open variable pulley until motor stops cycling. If cycling persists when pulley is fully opened, you must use next SMALLER pulley. Always use pulley size recommended by cooler manufacturer.
PN____PKG__QTY___WT 6122.....Bulk.....20....17.5 6123.....Bag.....10......7.5 6124.....Pkg.......6......5.5
|
|
|
|
6128-6129
ZINC VARIABLE MOTOR PULLEYS
3-1/4" x 5/8"- 1/3 HP
5/8" Bore Pulleys Have Keyways
IMPORTANT: Variable Pulleys must be opened 2-1/2 to 5 full turns (depending on air resistance) or motor will overheat. If motor cycles (stops and starts due to over-heating), open variable pulley until motor stops cycling. If cycling persists when pulley is fully opened, you must use next SMALLER pulley. Always use pulley size recommended by cooler manufacturer.
PN____PKG__QTY___WT 6128.....Bulk.....20....17.9 6129.....Bag......10.....9.2 |
|
|
|
6143 to 6145
ZINC VARIABLE MOTOR PULLEYS
3-1/2" x 1/2"- 1/2 HP
IMPORTANT: Variable Pulleys must be opened 2-1/2 to 5 full turns (depending on air resistance) or motor will overheat. If motor cycles (stops and starts due to over-heating), open variable pulley until motor stops cycling. If cycling persists when pulley is fully opened, you must use next SMALLER pulley. Always use pulley size recommended by cooler manufacturer.
PN____PKG__QTY___WT 6143.....Bulk.....20....20.3 6144.....Bag......10....10.0 6145.....Pkg.......6......6.3 |
|
|
|
|
|
6146-6147
ZINC VARIABLE MOTOR PULLEYS
3-1/2" x 5/8"- 1/2 HP
5/8" Bore Pulleys Have Keyways
IMPORTANT: Variable Pulleys must be opened 2-1/2 to 5 full turns (depending on air resistance) or motor will overheat. If motor cycles (stops and starts due to over-heating), open variable pulley until motor stops cycling. If cycling persists when pulley is fully opened, you must use next SMALLER pulley. Always use pulley size recommended by cooler manufacturer.
PN____PKG__QTY___WT 6146.....Bag.....10....10.8 6147.....Bulk.....20...21.1 |
|
|
|
6148 to 6151
ZINC VARIABLE MOTOR PULLEYS
3-3/4" x 1/2"- 1/2 or 3/4 HP
IMPORTANT: Variable Pulleys must be opened 2-1/2 to 5 full turns (depending on air resistance) or motor will overheat. If motor cycles (stops and starts due to over-heating), open variable pulley until motor stops cycling. If cycling persists when pulley is fully opened, you must use next SMALLER pulley. Always use pulley size recommended by cooler manufacturer.
PN____PKG__QTY___WT 6148.....Bulk.....20....23.1 6149.....Pkg.......6......7.2 6151.....Bag.....10....11.7 |
|
|
|
6152-6153
ZINC VARIABLE MOTOR PULLEYS
3-3/4" x 5/8"- 1/2 or 3/4 HP
5/8" Bore Pulleys Have Keyways
IMPORTANT: Variable Pulleys must be opened 2-1/2 to 5 full turns (depending on air resistance) or motor will overheat. If motor cycles (stops and starts due to over-heating), open variable pulley until motor stops cycling. If cycling persists when pulley is fully opened, you must use next SMALLER pulley. Always use pulley size recommended by cooler manufacturer.
PN____PKG__QTY___WT 6152.....Bulk.....20....25.5 6153.....Bag.....10.....12.8 |
|
|
|
6170
ZINC VARIABLE MOTOR PULLEYS
4" x 1/2"- 1 HP
IMPORTANT: Variable Pulleys must be opened 2-1/2 to 5 full turns (depending on air resistance) or motor will overheat. If motor cycles (stops and starts due to over-heating), open variable pulley until motor stops cycling. If cycling persists when pulley is fully opened, you must use next SMALLER pulley. Always use pulley size recommended by cooler manufacturer.
PN____PKG__QTY___WT 6170.....Bag.....10.....19.0 |
|
|
|
6171 to 9173
ZINC VARIABLE MOTOR PULLEYS
4" x 5/8"- 1 HP
♦For 1 H.P. Single Inlet Coolers
PN____PKG__QTY___WT 6171.....Bulk.....20....36.0 6172.....Bag......10....17.3 6173.....Pkg.......6.....10.1 |
|
|
|
|
|
6190-6191
CAST IRON VARIABLE MOTOR PULLEYS
3-1/4" x 1/2"- 1 HP (same as 1VL34)
PN____PKG__QTY___WT 6190.....Bulk.....20....25.6 6191.....Bag.......6......7.6 |
|
|
|
6192-6193
CAST IRON VARIABLE MOTOR PULLEYS
3-1/2" x 1/2"- 1 HP
PN____PKG__QTY___WT 6192.....Bulk.....20....29.0 6193.....Bag.......6......8.6
|
|
|
|
6194-6195
CAST IRON VARIABLE MOTOR PULLEYS
3-3/4" x 1/2"- 1/2 or 3/4 HP (same as 1VL40)
PN____PKG__QTY___WT 6194.....Bulk.....20....30.3 6195.....Bag.......6......9.3
|
|
|
|
6196
CAST IRON VARIABLE MOTOR PULLEYS
3-3/4" x 5/8"- 1/2 or 3/4 HP
PKG___QTY___WT Bulk........6......9.0 |
|
|
|
6197
CAST IRON VARIABLE MOTOR PULLEYS
4.15" x 1/2"- 1 HP
For 1 H.P. Single Inlet Coolers
PKG___QTY___WT Pkg.........6.....12.5 |
|
|
|
|
|
6198-6199
CAST IRON VARIABLE MOTOR PULLEYS
4.15" x 5/8"- 1 HP (same as 1VL44)
For 1 H.P. Single Inlet Coolers
PN____PKG__QTY___WT 6198.....Bulk.....6....12.2 6199.....Bag......6.....8.1
|
|
|
|
6207 to 62985
ZINC FIXED MOTOR PULLEYS
5/8" Bore Pulleys Have Keyways
(Package - Bulk)
PN_____SIZE___QTY__WT 6207......2" x ½"....20….5.7 6209......2" x ⅝"...20….5.3 6211…2¼" x ½"...20….9.2 6219...2¼" x ⅝"...20….8.6 6235...2½" x ½"....20….9.5 6237...2½" x ⅝"...20….8.8 6240...2¾" x ½"....20….7.9 6255...2¾" x ⅝"...20…10.4 6262......3" x ½"....20...9.2 6271......3" x ⅝"...20...9.7 6280...3¼" x ½"....20…10.6 6286...3¼" x ⅝"...20…10.1 6293...3½" x ½"....20….9.4 6298...3½" x ⅝"...20…10.1 6298......4" x ⅝"...20..13.5
|
|
|
|
6215-6216
1/3 HP ZINC FIXED MOTOR PULLEYS
PACKAGED
2-1/4" Dia. x 1/2" Bore
Note: Fixed pulleys below are sized to avoid overloading cooler motors that are installed without using an ammeter.
PN____PKG__QTY___WT 6215.....Bag.....10......4.8 6216.....Card.....6......2.9 |
|
|
|
6244-6245
1/2 HP ZINC FIXED MOTOR PULLEYS
PACKAGED
2-3/4" Dia. x 1/2" Bore
Note: Fixed pulleys below are sized to avoid overloading cooler motors that are installed without using an ammeter.
PN____PKG__QTY___WT 6244.....Bag.....10......4.1 6245.....Pkg.......6......2.7 |
|
|
|
6264-6265
3/4 HP ZINC FIXED MOTOR PULLEYS
PACKAGED
3" Dia. x 1/2" Bore
Note: Fixed pulleys below are sized to avoid overloading cooler motors that are installed without using an ammeter.
PN____PKG__QTY___WT 6264.....Bag.....10......5.2 6265.....Pkg.......6......3.3 |
|
|
|
|
|
6307 to 6341
ZINC BLOWER MOTOR PULLEYS
WITH KEYWAY
(Package - Label)
PN_____SIZE__QTY__WT 6307.....7" x ⅝"....5.....5.7 6309.....7" x ¾"....5.....5.1 6310.....7" x 1".....5.....5.2 6311.....8" x ⅝"....5.....6.3 6312.....8" x ¾"....5.....5.8 6314.....8" x 1".....5….5.7 6319.....9" x ¾"....5.....8.9 6321.....9" x 1".....5.....8.6 6323...10" x ¾"....5.....9.2 6324...10" x 1".....5.....8.5 6327...11" x ⅝"....5.....9.5 6328...11" x ¾"....5.....9.5 6330...11" x 1".....5....10.9 6336...12" x ¾"....5...11.6 6338...12" x 1".....5...11.6 6340...14" x ¾"....5...14.8 6341...14" x 1".....5...14.3 |
|
|
